King Kutter Tiller 999995 Bedienungsanleitung

2150 Eastern Avenue. Gallipolis, Ohio 45631 ROTARY TILLER OPERATOR MANUAL Part No 999995 www.kingkutter.com

10 Figure E Figure F Figure G Figure H Figure I Figure J

SAFETY TRAINING  Safety is a primary concern in the design and manufacturing of our product. Un-fortunately, our efforts to provide safe equipmen

PREPARTION  Never operate the tractor and tiller until you have read and completely under-stand this manual, the Tractor Operator

13 OPERATIONAL SAFETY  The use of this equipment is subject to certain hazards that cannot be protected against by the mechanical means or product

OPERATIONAL SAFETY continued...  Never allow the tilling tines to contact such items. Never assume an area is clear. Always Check!

15 OPERATIONAL SAFETY continued...  Pass rotary tiller diagonally through sharp dips and avoid sharp drops to prevent ―hanging up‖ tractor and rota

16 ATTACHING TO TRACTOR STEP 1 Attach to tractor's category 1 three point hitch as desc

17 ATTACHING TO TRACTOR continued... STEP 5 Place and hold inner PTO shaft section next to outer section and check if PTO shaft is too

18 SIZING PTO SHAFT STEP 1 Cutting the PTO shaft to length. NOTE: Be sure to cut equal lengths of each PTO shaft section. Clamp

19 OPERATING INSTRUCTIONS STEP 1 Before each use perform the maintenance described in maintenance section (page 20). STEP2 Read, understan

Never travel at a fast ground speed while using the tiller, this could damage it. Never attempt to turn the tractor or travel in reverse with the P

 Be sure electrical outlets and tools are properly grounded  Use adequate light for the job at hand.  Make sure there is plenty ventilat

22 SAFETY SIGN LOCATIONS The types of safety signs and locations on the equipment are shown in the illustration below. Good safety requires that you

23 1

24 2 3

25 4 5

26 6 7 MODEL NO. DESCRIPTION SN# XXXXXXXXXX

27 NOTES:

TILLER: EXPLODED VIEW 28

Ref. No. Part Name TG-48 TG-72 TG-60 1 Lift Arm Brace 380108 380108 380108 2 Lift Arm (Left hand) 310085 310085 310085 3 Lift Arm (Right ha

TO THE PURCHASER This manual contains valuable information about your new King Kutter II Rotary Tiller. It has been carefully prepared to giv

30 Ref. No. Part Name 147122 Part No. 1 Safety Shield 124311 2 Roll Pin 170120 3 Male Tube End Yoke 151045 4 Female Tube End Yoke 151050 5

31 TG SERIES OUT-BOARD HUB 184070 Ref. No. Part Name 184070 1 Hub Housing 902341 2 Cap 902342 3 Self Aligning Ball Bearing (1310) 902019 4 Se

32 TG SERIES GEARBOX 184069

33 Ref. No. Part Name Part Number 1 Retaining Ring 90mm 902005 2 Retaining Ring 40mm 902006 3 Pressure Plate Plug 1/2‖ - 14 NPT 902007 4 Sq. H

34 TG SERIES TOP GEARBOX ASSEMBLY

35 TG SERIES TOP GEARBOX PARTS LIST Ref. No. Part Name Part Number 1 Retaining Ring 72mm 902301 2 Retaining Ring 40mm 902302 3 Housing RTA - 50

36 1. Limited Warranty. King Kutter, Inc. (―King Kutter‖), P.O. Box 1200, Winfield, Alabama 35594, warrants to the original retail pur-chaser (―Purcha

It is the purchaser and/or operator’s responsibility to….  Read and understand the information contained in this manual.  Operate, lubricate,

5 CONTENTS ITEM PAGE Safety ... 6 Assembly Instructions ...

SAFETY READ AND FOLLOW THE INSTRUC-TIONS IN THIS MANUAL AND ESPE-CIALLY IN THE SAFETY SECTION. FAILURE TO DO SO CAN RESULT IN SERIOUS IN

EQUIPMENT SAFETY GUIDELINES  Safety of the operator and bystanders is one of the main concerns in designing and devel-oping a tiller. However, ev

8 ROTARY TILLER ASSEMBLY INSTRUCTIONS STEP 1 With rotary tiller still in crate, lay flat on a level surface. Cut banding straps on

9 STEP 6 Fill side gearbox using gear oil until the oil begins to overflow from the check plug hole. See Figure F on next page. STEP 7